Terluran GP-22: specs and equivalent grades
INEOS Styrolution easy-flow general purpose injection molding ABS with high impact and heat resistance, used widely for housings. Published data, grades from other producers to ask about, and how to request a quote from one gaylord.
Request a QuoteThe short answer
Terluran GP-22 is INEOS Styrolution's easy-flow, general purpose injection molding ABS with high resistance to impact and heat distortion, used widely for housings, appliances and household goods. Published melt volume rate is 19 cm³/10 min, measured at 220°C / 428°F, 10 kg, ISO 1133, and specific gravity is 1.04 (ISO 1183). Charpy notched impact is 22 kJ/m² at 23°C (ISO 179). INEOS Styrolution still owns Terluran; we found no ownership change as of October 2026. Grades from other producers to ask about include Cycolac MG47 and POLYLAC PA-757. They are not identical, so compare the data sheets and run a trial before switching.
Also written as: Terluran® GP-22, TERLURAN GP-22. INEOS Styrolution’s product page lists grade versions Terluran GP-22 NR (natural) and Terluran GP-22 BK10009 (black). Quote the full code, including any color, from your drawing or bag label.
Buying Terluran GP-22: one gaylord to a railcar · supplier COA on every prime lot · ships from 22+ partner warehouse locations · a polymer chemist checks the grade code before we quote · we aim to quote within one to three business days
Have a part number or drawing callout?
Paste it as written. A polymer chemist will tell you which grade it calls for, suggest equivalents and quote it by email.
Terluran GP-22 specs from the data sheet
Typical values for uncolored product from INEOS Styrolution's Terluran GP-22 product page (ISO values from the EMEA view, ASTM values from the Americas view). Typical values are not specifications; the lot COA shows what you actually receive. Values only compare at the same test method and condition.
| Property | Value | Test method or note |
|---|---|---|
| Producer (brand owner) | INEOS Styrolution | No ownership change found as of October 2026 |
| Polymer | ABS, general purpose, easy flow | |
| Process | Injection molding | INEOS Styrolution product page |
| Melt volume rate | 19 cm³/10 min | 220°C / 428°F, 10 kg, ISO 1133 |
| Melt volume rate | 4.8 cm³/10 min | 230°C / 446°F, 3.8 kg, ASTM D1238 |
| Specific gravity | 1.04 | ASTM D792, ISO 1183 |
| Tensile modulus | 2300 MPa | ISO 527 |
| Tensile strength at yield | 45 MPa (6,520 psi, ASTM D638) | ISO 527, 23°C |
| Nominal strain at break | 10 % | ISO 527, 23°C |
| Flexural modulus / strength | 334,000 psi (about 2300 MPa) / 65 MPa | Modulus ASTM D790; strength ISO 178 |
| Charpy notched impact | 22 kJ/m² at 23°C; 8 kJ/m² at −30°C | ISO 179/1eA |
| Notched Izod impact | 5.6 ft-lb/in (about 300 J/m) at 23°C | ASTM D256 |
| HDT at 1.8 MPa, annealed | 94°C / 201°F | ISO 75, method A, annealed 4 h at 80°C |
| HDT at 0.45 MPa, annealed | 99°C / 210°F | ISO 75, method B, annealed 4 h at 80°C |
| Vicat softening temperature | 105°C / 221°F (A50); 96°C / 205°F (B50) | ISO 306 |
| Ball indentation hardness | 97 MPa | ISO 2039-1 |
| Molding shrinkage | 0.4–0.7 % | ISO 294-4 |
| Water absorption | 0.22 % at 23°C / 50% RH; 1.0 % saturated | ISO 62 |
| Drying | 80°C / 176°F for 2–4 h | INEOS Styrolution processing data (the Americas view shows 175°F) |
| Melt temperature | 220–260°C / 428–500°F | INEOS Styrolution processing data |
| Mold temperature | 85–140°F (about 30–60°C) | Americas view; the ISO view gives 30–80°C |
| Food contact | INEOS Styrolution lists FDA and EU food-contact declarations for the natural (NR) version as documents on its Americas product page (download needs a login). Ask for the current letter for your exact use. |
Source data sheets are listed at the bottom of this page. Confirm against the current sheet for your exact grade code and color.
ABS picks up moisture (0.22% at 23°C / 50% RH on this sheet). Dry to the published 80°C for 2–4 h before molding; wet ABS shows splay and silver streaks.
Grades to ask about instead of Terluran GP-22
These grades from other producers have similar published specs. None is a drop-in replacement: additive packages, flow at molding shear rates, color and approvals differ. If your part, drawing or customer approval names Terluran GP-22, any change needs your approval and usually a trial.
| Grade | Producer | Melt flow | Density | Key property | How it compares |
|---|---|---|---|---|---|
| Cycolac MG47 | NexPoint Materials (formerly SABIC) | 18 g/10 min (220°C / 428°F, 10 kg, ISO 1133); 5.6 g/10 min (230°C / 3.8 kg, ASTM D1238) | 1.04 (ASTM D792, ISO 1183) | Charpy notched 26 kJ/m² at 23°C (ISO 179/1eA); notched Izod 320 J/m (ASTM D256); HDT 1.8 MPa unannealed 81°C (ISO 75-2/Af) | Close match. Multi-purpose injection molding ABS with similar flow, density and impact; UL 94 HB at 1.5 mm. Note the flow figure is mass (g/10 min), not volume, and HDT here is unannealed. Sold in the Americas and Europe by NexPoint Materials since August 3, 2026, when SABIC closed the sale of that business; NexPoint says formulations and specifications are unchanged. Quote this alternative › |
| POLYLAC PA-757 | Chi Mei | 19 cm³/10 min (220°C / 428°F, 10 kg, ISO 1133) | 1.05 (ASTM D792, ISO 1183) | Charpy notched 21 kJ/m² at 23°C (ISO 179); notched Izod 3.9 ft-lb/in (about 208 J/m) at 3.2 mm (ASTM D256); HDT 1.8 MPa annealed 98°C (ISO 75/A) | Close match on flow, density and Charpy impact; lower notched Izod on the ASTM sheet (about 208 vs 300 J/m) and slightly higher annealed HDT. CHIMEI describes it as high gloss, medium impact, for appliance, office equipment and electronics housings. UL 94 HB at 1.5 mm. Widely available; check color matching if you switch mid-program. Quote this alternative › |
From each producer’s published data. Brand owners and grade names change; confirm on the current data sheet.
Typical uses for Terluran GP-22
From INEOS Styrolution's Terluran GP-22 product page:
- Appliance housings
- Household and sanitary appliances
- Toys
- Automotive components
- Consumer products
What to check before you switch
- Compare flow on the same basis: Terluran GP-22 lists melt volume rate (cm³/10 min) at 220°C / 10 kg, and some sheets list mass flow (g/10 min) or 230°C / 3.8 kg.
- Compare HDT annealed to annealed and at the same load; Terluran's 94°C is annealed at 1.8 MPa, while Cycolac MG47's 81°C is unannealed.
- If the part is colored, run a color match on the alternative; ABS base color differs between producers.
- If the housing needs a flame rating, confirm the UL file and thickness for the exact grade and color you buy.
- Ask for the producer's food-contact or regulatory letter for the exact grade if the part needs one.
- Run a trial lot and check shrinkage, gloss, cycle time and impact before you switch production.
Buying Terluran GP-22: price, lead time and lot size
- Lot size. From one gaylord to a railcar. See gaylord, LTL and truckload for typical weights per box.
- Where it ships from. 22+ partner warehouse locations. Material already in a partner warehouse usually moves sooner than a grade that has to come from the producer; your quote says which applies.
- Price. We do not publish prices because they move with feedstock, freight and order size. What moves your price most: lot size, color, ship-to region, and whether you need Terluran GP-22 itself or can accept a matched alternative. See how resin is priced and the monthly market update.
- Paperwork. Supplier COA on every prime lot (what a COA shows). Ask for the producer’s regulatory letter or UL file if your part needs them.
- Trying an alternative? Start with one gaylord as a trial lot, molded and checked before you commit a full release.
- If Terluran GP-22 itself is not available. Some branded grades are sold only through the producer’s own channels or go on allocation. If we cannot source it, we tell you, then quote a matched alternative with a side-by-side comparison.
Send the grade code, your annual volume and ship-to location. A polymer chemist checks it before we quote; we have been in the resin business for 30+ years. For several grades at once, use the resin RFQ template.
Trade names belong to their owners. ResinBridge is not affiliated with these producers; grade names are used only to identify the material. Data reflects published sheets as of October 2026.
Sources
- INEOS Styrolution Terluran GP-22 product page and typical values
- INEOS Styrolution ABS page
- Cycolac MG47 (Americas) UL Prospector data sheet, SABIC data (PDF)
- NexPoint Materials transition hub
- CHIMEI POLYLAC general ABS grade list
- CHIMEI POLYLAC PA-757 ISO data sheet, Jan 2025 (CHIMEI document, distributor-hosted)
- CHIMEI POLYLAC PA-757 ASTM data sheet, Sep 2023 (CHIMEI document, distributor-hosted)
Common questions
What is Terluran GP-22?
Terluran GP-22 is INEOS Styrolution's easy-flow, general purpose injection molding ABS with high impact and heat distortion resistance, used widely for housings.
What is the melt flow of Terluran GP-22?
Its melt volume rate is 19 cm³/10 min, measured at 220°C / 428°F, 10 kg, ISO 1133. At 230°C / 3.8 kg (ASTM D1238) it is 4.8 cm³/10 min.
What is equivalent to Terluran GP-22?
Grades from other producers to ask about include Cycolac MG47 and POLYLAC PA-757. None is identical; compare data sheets and run a trial, and get approval if your part names Terluran GP-22.
How should Terluran GP-22 be dried?
The published processing data says 80°C / 176°F for 2–4 hours, with melt temperature 220–260°C and mold temperature 30–60°C.
Can ResinBridge supply Terluran GP-22?
We quote Terluran GP-22 when our supply partners can source it. If they cannot, we say so up front and quote a matched alternative, named on the quote with its data sheet, so you can decide whether to trial it.
If your grade is not listed, tell us what you run. We source commodity, engineering and specialty resins.
Need Terluran GP-22 or an equivalent?
A polymer chemist reviews every request, then matches your grade or finds a matched alternative and prices it.
What to send for an accurate quote
- The grade name, from any supplier, or a data sheet
- Color (natural, black or a custom match)
- Fill type and percentage, if any
- Melt flow, if you know it
- Quantity for this order and what you use in a year
- Ship-to city and state or province
Quote Terluran GP-22 or a matched alternative
A polymer chemist checks the data sheet and tells you exactly what you would get before you order.
Request a QuoteNot sure which grade fits your part?
Send the grade you run now, or describe the part.